|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
KOA SPEER ELECTRONICS, INC. TN-196 R12 AHA 1/25/07 Ceramic Chip Capacitors Type NPO, X5R, X7R, Y5V 1. CERTIFIED CERTIFIED General 1-1 Range of Application This document applies to miniaturized ceramic chip capacitors for applications in circuits of electronic devices. 2. Type Designation The type designation shall be the following form: New Type NPO Dielectric NPO X5R X7R Y5V 0805 Size 0402 0603 0805 1206 1210 A C E H I J K H Voltage = 10V = 16V = 25V = 50V = 100V = 200V = 6.3V T Termination Material T: Sn TD Packaging TP: 7" 2mm pitch (0402 only) TD: 7" paper tape TE: 7" embossed plastic TDB: 13" paper tape TEB: 13" embossed plastic 101 Capacitance Code NPO, X5R, X7R, Y5V - 2 significant digits + no. of zeros. R indicates decimal point. K Tolerance B C D F G J K M Z = 0.1pF = 0.25pF = 0.5pF = 1% = 2% = 5% = 10% = 20% = +80%, -20% 3. Dimensions and Construction L W Table 1 Case Code 0402 0603 L .040 .004 (1.00 .10) .063 .006 (1.60 .15) .079 .008 (2.01 .20) .126 .008 (3.20 .20) .126 .008 (3.20 .20) Dimensions in inches (mm) W .020 .004 (.50 .10) .032 .006 (.81 .15) .049 .008 (1.25 .20) .063 .008 (1.60 .20) .098 .008 (2.50 .20) t (Max.) .021 (.55) .035 (.90) .051 (1.30) .059 (1.50) .067 (1.70) d .010 .006 (.25 .15) .014 .006 (.35 .15) .020 .010 (.50 .25) .020 .010 (.50 .25) .020 .010 (.50 .25) t d Ceramic Body d 0805 1206 1210 Solder Plating (Sn) Ni Plating Electrodes Silver Metallization PAGE 1 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 4. Terminations Standard Nickel Barrier Solder Plated 5. Applications and Ratings Capacitance Capacitance Range Tolerance* .47pF~8.2pF= C:0.25pF 5.6pF~8.2pF= D0.5pF 10pF~10000pF= F:1%, G:2%, J:5% Voltage Ratings Dissipation Factor Operating Temperature Insulation Resistance Dielectric T.C.C. Test Voltage NPO 0.47pF 0.039F 16V 25V 50V 100V 200V For Values >30pF: 0.1% max., 30pF: 0 30 ppm/C 1.0 0.2 Vrms Q = 400 + 20 x C DF = 1/Q C is in pF -55C to +125C +25C 100,000M min. or 1000 M - F min. whichever is less X5R 0.068F 10F K: 10% 6.3V 10V 10V 16V 25V 50V 100V 200V 10V 16V 25V 50V 6.3 = 7.3% 10 = 5.0% For 50 & 100 volts 2.5% max. 25 = 3.0% 16 = 3.5% 16V & 25V = 7.0% 50V = 5.0% 15% (0 VDC) 1.0 0.2 Vrms -55C to +85C +25C 100,000M min. or 500 M - F min. whichever is less X7R 100pF 4.7F K: 10% 15% (0 VDC) 1.0 0.2 Vrms -55C to +125C +25C 100,000M min. or 1000 M - F min. whichever is less Y5V 2200pF 10F Z: +80, -20% +22% to -82% 1.0 0.2 Vrms max. -30C to +85C +25C 10,000M min. or 1000 M - F min. whichever is less * Special tolerances available, please consult factory. PAGE 2 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 6. NPO Capacitance Voltage Availability Size Capacitance values pF F Cap. Code 0.47 0.56 0.68 0.82 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 R47 R56 R68 R82 1R0 1R2 1R5 1R8 2R2 2R7 3R3 3R9 4R7 5R6 6R8 8R2 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 0402* WVDC 16 (C) 25 (E) 50 (H) 0603* 50 (H) 100 (I) 50 (H) 0805 100 (I) 200 (J) 50 (H) 1206 100 (I) 200 (J) 50 (H) 1210 200 (J) .0001 .00012 .00015 .00018 .00022 .00027 .00033 .00039 .00047 .00056 .00068 .00082 .0010 .0012 .0015 .0018 .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 * IR and vapor phase solder only recommended Capacitance tolerance available: .47pF~8.2pF = C: 0.25pF, 5.6pF~8.2pF = D: 0.5pF 10pF~10000pF = F: 1%, G: 2%, J: 5% PAGE 3 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 7. X5R Capacitance Voltage Availability Size Capacitance values pF F 100 150 220 330 470 680 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 3.3 4.7 6.8 10 22 47 100 0402 6.3 (K) 10 (A) 16 (C) 6.3 (K) 0603 10 (A) 16 (C) 25 (E) 6.3 (K) 0805 10 (A) 16 (C) 25 (E) 6.3 (K) 1206 10 (A) 16 (C) 25 (E) 1210 6.3 (K) 10 (A) Capacitance tolerance available: 10% PAGE 4 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 8. X7R Capacitance Voltage Availability Size Capacitance values pF 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 270000 330000 390000 470000 560000 680000 1000000 1200000 1500000 1800000 2200000 3900000 4700000 F .0001 .00012 .00015 .00018 .00022 .00027 .00033 .00039 .00047 .00056 .00068 .00082 .0010 .0012 .0015 .0018 .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100 .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 1.00 1.20 1.50 1.80 2.20 3.90 4.70 0402* 0603* 0805 1206 1210 10 16 25 50 10 16 25 50 10 16 25 50 100 200 10 16 25 50 100 200 50 100 200 Cap. Code (A) (C) (E) (H) (A) (C) (E) (H) (A) (C) (E) (H) (I) (J) (A) (C) (E) (H) (I) (J) (H) (I) (J) 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 105 125 155 185 225 395 475 * IR and vapor phase solder only recommended Capacitance tolerance available: 10% PAGE 5 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 9. Y5V Capacitance Voltage Availability Size Capacitance values pF 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 180000 220000 270000 330000 390000 470000 560000 680000 820000 1000000 1200000 1500000 1800000 2200000 2700000 3300000 3900000 4700000 5600000 6800000 10000000 22000000 F .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100 .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 .820 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 10 22 Cap. Code 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 395 475 565 685 106 226 0402* 10 (A) 16 (C) 10 (A) 0603* 16 (C) 25 (E) 50 (H) 10 (A) 16 (C) 0805 25 (E) 50 (H) 10 (A) 1206 16 (C) 25 (E) 50 (H) * IR and vapor phase solder only recommended Capacitance tolerance available: +80, -20% PAGE 6 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 10. Typical Impedance Characteristics - NPO Variation of Impedance with Cap Value Impedance vs. Frequency 0805 - C0G (NP0) 10 pF vs. 100 pF vs. 1000 pF 100,000 +2 10,000 Capacitance vs. Frequency % Capacitance +1 0 -1 -2 Impedance, 1,000 100 10.0 10 pF 1.0 0.1 1 10 100 100 pF 1000 pF 1000 1kHz 10 kHz 100 kHz 1 MHz 10 MHz Frequency Frequency, MHz Insulation Resistance (Ohm-Farads) Temperature Coefficient Typical Capacitance Change Envelope: 0 30 ppm/C Insulation Resistance vs Temperature 10,000 % Capacitance 1,000 +0.5 0 -0.5 100 -55 -35 -15 +5 +25 +45 +65 +85 +105 +125 0 Temperature C +20 +25 +40 +60 +80 +100 Temperature C Variation of Impedance with Chip Size Impedance vs. Frequency 1000 pF - C0G (NP0) 10 1206 0805 1812 1210 1.0 Variation of Impedance with Ceramic Formulation Impedance vs. Frequency 1000 pF - C0G (NP0) vs X7R 0805 10.00 X7R NPO Impedance, Impedance, 1000 1.00 0.10 0.1 10 100 0.01 10 100 1000 Frequency, MHz Frequency, MHz PAGE 7 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 11. Typical Impedance Characteristics - X5R Temperature Coefficient +20 +15 Insulation Resistance (Ohm-Farads) Insulation Resistance vs Temperature 10,000 % Capacitance +10 +5 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 +80 1,000 100 0 Temperature C +20 +25 +40 +60 +80 +100 Temperature C PAGE 8 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 12. Typical Impedance Characteristics - X7R Variation of Impedance with Cap Value Impedance vs. Frequency 1,000 pF vs. 10,000 pF - X7R 0805 10.00 1,000 pF +20 10,000 pF Capacitance vs. Frequency % Capacitance Impedance, +10 0 -10 -20 1.00 0.10 0.01 10 100 1000 1kHz 10 kHz 100 kHz 1 MHz 10 MHz Frequency, MHz Frequency Insulation Resistance (Ohm-Farads) Temperature Coefficient +12 +6 Insulation Resistance vs Temperature 10,000 % Capacitance 0 -6 -12 -18 -24 -75 -50 -25 0 +25 +50 +75 +100 +125 1,000 100 0 Temperature C +20 +25 +40 +60 +80 +100 Temperature C Variation of Impedance with Chip Size Impedance vs. Frequency 10,000 pF - X7R 10 1206 0805 1210 Variation of Impedance with Chip Size Impedance vs. Frequency 100,000 pF - X7R 10 1206 0805 1210 1.0 Impedance, 1.0 Impedance, 1,000 0.1 0.1 .01 1 10 100 .01 1 10 100 1,000 Frequency, MHz Frequency, MHz PAGE 9 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 13. Typical Impedance Characteristics - Y5V 0.22 F - 0805 Impedance vs. Frequency 1,000 100 10,000 1,000 0.1 F - 0603 Impedance vs. Frequency Impedance () Impedance () 100 10 1 0.1 0.01 10,000 10 1 0.1 0.01 10,000 100,000 1,000,000 10,000,000 100,000 1,000,000 10,000,000 Frequency (MHz) Frequency (MHz) Insulation Resistance (Ohm-Farads) Temperature Coefficient +20 +10 0 -10 -20 -30 -40 -50 -60 -70 -80 -55 -35 -15 +5 +25 +45 +65 +85 +105 +125 Insulation Resistance vs. Temperature 10,000 % Capacitance 1,000 100 0 Temperature C +20 +30 +40 +50 +60 +70 +80 +85 Temperature C 1 F - 1206 Impedance vs. Frequency 1,000 +40 100 Capacitance Change vs. DC Bias Voltage Impedance () +20 c/c (%) 10 1 0.1 0 -20 -40 -60 -80 0.01 10,000 100,000 1,000,000 10,000,000 -100 0 20 40 60 80 100 Frequency (MHz) DC Bias Voltage PAGE 10 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 14. Tape and Reel Quantities All tape and reel specifications are in compliance with RS481. 0402 TE = 7" (178) Plastic B = 13" (330) Plastic T = 7" (178) Paper D = 13" (330) Paper N/A N/A 15,000 N/A 0603 N/A N/A 4,000 10,000 0805 *2,000/4,000 10,000 4,000 10,000 Dimensions in inches (mm) 1206 2,000 10,000 4,000 10,000 1210 *2,000/4,000 10,000 4,000 10,000 * Z5U 0805 50V 104pf = 2k, 1206 50V 184pf = 2k, 1210 50V 274pf = 2k; Y5V 0805 50V 124pf = 2k, 25V 394pf = 2k, 16V 474pf = 2k, 1206 25V 564pf = 2k, 16V 824pf = 2k, 1210 50V 334pf = 2k, 25V 105pf = 2k; X7R 0805 100V 123pf = 2k, 50V 101pf = 2k, 16V 154pf = 2k, 1206 100V 393pf = 2k, 25V 124pf = 2k, 16V 394pf = 2k; NPO 0805 100V 391pf = 2k, 50V 561pf = 2k, 1206 100V 152pf = 2k, 50V 152pf = 2k, 1210 100V 182pf = 2k, 50V 272pf = 2k 0805 Y5VCTE 225 Z , 1206 Y5VCTE 335 Z, 1210 Y5VETE 475 Z = 3k 15. Reel Dimensions 1.575 (40) min. Access hole at slot location. W3 (Includes flange distortion at outer edge). W2 (Measured at hub). B* (Arbor hole dia.) C A D* N (Hub dia.) Full radius* W1 (Measured at hub). * Drive spokes optional. If used, asterisked dimensions apply. Tape slot in core for tape start. 0.98 (2.5) min. width, .394 (10) min. depth. Dimensions in inches (mm) Tape Size(1) 8mm A Max. 7.0 (178) 12.992 (330) B* Min. C D* Min. N Min. W1 .331 - 0.0 (8.4 1.0 ) - 0.0 .488 - 0.0 (12.4 2.0 ) - 0.0 .078 .050 W2 Max. .567 14.4 .724 (18.4) W3 .311 (7.9 Min.) .429 (10.9 Max.) .469 (11.9 Min.) .607 (15.4 Max.) .059 (1.5) .512 .008 (13.0 0.20) .795 (20.2) 1.969 (50) 12mm Metric dimensions will govern. English measurements rounded and for reference only. (1) For tape sizes 16mm and 24mm (used with chip size 3 3640) consult EIA RS-481 latest revision. Bolivar Drive PAGE 11 OF 13 P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 16. Carrier Tape Specifications Embossed plastic 8 & 12mm T2 T Deformation between embossments Top cover tape 10 pitches cumulative tolerance on tape 0.008 (0.2) D0 P2 P0 Embossment E G1 See note 3 A0 F B0 W B1 K0 G2 See note 4 T1 For tape feeder reference only including draft concentric around B0 Center lines of cavity User direction of feed P1 Maximum cavity size, see note 1 D1 for components .079 x .047 (2.0 x 1.2) and larger 17. Dimensions Tape Size Constant 8mm and 12mm Tape Size Variable 8mm 12mm D0 .059 (1.5 .004 0.0 0.10 0.0 Dimensions in inches (mm) E P0 P2 T Max. .024 (0.600) T1 .004 (0.10) Max. G1 .030 (0.75) Min. See note 3 G2 .030 (0.75) Min. See note 4 .069 .004 .157 .004 .079 .002 ) (1.75 0.10) (4.0 0.10) (2.0 0.05) B1 Max. See note 6 .179 (4.55) .323 (8.2) D1 Min. See note 5 .039 (1.0) .059 (1.5) F P1 R Min. See note 2 .984 (25) 1.181 (30) T2 .098 (2.5 Max.) .256 (6.5 Max.) W .315 (8.0 .012 .004 0.3 0.1 A0B0K0 ) See note 1 .138 .002 .157 .004 (3.5 0.05) (4.0 0.10) .217 .002 .157 .004 (5.5 0.05) (4.0 0.10) .472 .012 (12.0 .30) See note 1 Notes: 1. A0, B0 and K0 are determined by the max. dimensions to the ends of the terminals extending from the components body and/or the body of the component. The clearance between the end of the terminals of the body of the components to the sides and depth of the cavity (A0, B0 and K0) must be within .002" (0.05)mm min. and .020" (0.50)mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples A & B). 2. Tape with components shall pass around radius "R" without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for .472" (12)mm embossed tape for reels with hub diameters approaching N min. (Table 4). 3. G1 dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 4. G2 dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 20 Maximum Component Rotation 6. B1 dimension is a reference dimension for tape feeder clearance only. Typical component cavity center line 20 Maximum Component Rotation Side or Front Sectional View Example "A" BO AO Typical component center line Top View Example "B" PAGE 12 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-196 R12 10 pitches cumulative tolerance on tape 0.008 (0.2) T D0 P2 E F W B0 G1 P1 Center lines of cavity G2 P0 18. Carrier Tape Specifications Punched paper tape 8 & 12mm Bottom cover tape Top cover tape T1 T1 Cavity size, see note 1 A0 User direction of feed 19. Dimensions Tape Size Constant 8mm and 12mm Tape Size Variable 8mm 12mm D0 .059 .004 - .000 0.1 0.0 ) Dimensions in inches (mm) E .069 .004 (1.75 0.10) P0 .157 .004 (4.0 0.10) P2 .079 .002 (2.0 0.05) T1 .004 (0.10) Max. G1 .030 (0.75) Min. G2 .030 (0.75) Min. R MIN .984 (25) See note 2 (1.5 - P1 .157 .004 (4.0 0.10) .157 .004 (4.0 .010) F .138 .002 (3.5 0.05) .217 .002 (5.5 0.05) W .315 .012 - .004 (8.0 0.3 ) - 0.1 .472 .012 (12.0 0.3) A0B0 See note 1 T See note 2 Notes: 1. A0, B0 and T are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the components to the sides and depth of the cavity (A0, B0 and T) must be within .002" (0.05) mm min. and .020" (0.50) mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples C & D). 20 Maximum Component Rotation 2. Tape with components shall pass around radius "R" without damage. T Typical component 3. .043" (1.1) mm base tape and .063" (1.6) mm max. 20 cavity center line BO for non-paper base compositions. Maximum Component Rotation Side or Front Sectional View Example "C" AO Typical component center line Top View Example "D" 20. Recommended Land Pattern Dimensions Component pads should be designed to achieve good solder filets and minimize component movement during reflow soldering. Pad dimensions are given below for multilayer ceramic capacitors for both reflow and wave soldering. The basis for these designs is: * Pad width equal to component width. It is permissible to decrease this to as low as 85% of component width but it is not advisable to go below this. * Pad overlap 0.5mm beneath component * Pad extension 0.5mm beyond components for reflow and 1.0mm for wave soldering C D C A B 22-1 Reflow Soldering Case Size 0402 0603 0805 1206 1210 A* 0.50 0.75 1.25 1.60 2.50 B* 1.70 2.30 3.00 4.00 4.00 C* 0.60 0.80 1.00 1.00 1.00 D* 0.50 0.70 1.00 2.00 2.00 22-2 Wave Soldering Case Size A* 0805 1.25 1206 1.60 1210 2.50 B* C* D* 4.00 1.50 1.00 5.00 1.50 2.00 5.00 1.50 2.00 * All dimensions are in millimeters unless otherwise specified. PAGE 13 OF 13 Bolivar Drive P.O. Box 547 Bradford, PA 16701 USA 814-362-5536 Fax 814-362-8883 www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. |
Price & Availability of NPO0805JT |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |